CRT connector loose
Perhaps we often
hear people say "oh TVku broken tube". The
question that arises then, is it true they were broken TV tube. The answer can not be
yes.Sometimes
we do not see the whole screen (distressed / or folding) so that there is a
black part on the top or bottom, sometimes if the damage is severe can only
horizontal lines across the TV screen kita.Orang that do not exist that we
diagnose the faulty tube tv.TV we are not broken but the broken tube in the vertical
sync.Then
there is also a screen that pressed the left or right section. It's also not because of
damage to the tube. For
this there are several possible damage broken: can the horizontal, Fly back
transformers, power supplies, or perhaps just an electrical voltage in your home
are too ngedrop.Then the
trapezoidal or depressed left, right, up and down. Typically
for this damage often occurs due to the deflection coil short / shorting because
this emailnya.kerusakan peeling layers if left unchecked will spread to the
horizontal and the other or worse tv will make us totally dead.Subsequent
damage is the dominant color tv looks a certain color or no color that is
unusual or loss of color. For this
damage could be a tube television is really broken. but
it helps us to diagnose their own destruction if we simply understand a little
knowledge of electronics.To
damage this color, it needs to do is look at what the dominant color or color of
what was lost. (Red,
green, blue) because it is technically a color tv is the merger of the three
elements of color.Once
we know what color is missing, we can do the next step is to try to repair or
call a service when we are not able to fix it.The
question may be how to find the damage or repair this damage?Here
I will try to write a little trouble shooting on this type of damage is
simple:after
we open the casing, the rear of the tube there is a small PCB and attached to
the back of the tube. It is the color of the amplifier PCB.
usually frequent breakdowns there.
The
first step to do is clean the surface of the PCB deengan thiner, then doing
strengthening soldiran there by way of re-soldering the legs disana.keretakan
soldiran components that are not clearly visible to the eye can cause color
damage earlier. and sometimes to move sdh
damage can be resolved. Nb:
for TV brands National / Panasonic usually this step can not recover damages
even if the damage is the loss soldiran initially. steps
to be taken is to replace the transistor amplifier in the PCB color (red, green,
blue) all three at once.If
after repeated soldir but the color is still not normal, now it's our turn to
check it true that we are indeed broken TV tube or indeed any other damage.
The trick is quite
simple.Take
our multi meter cable, which can be black or merah.kemudian plug one end on the
ground from our TV (casing), then turn on the TV, then one end of the cable
before we plug it into the tube cathode leg is in a small PCB earlier. There are 3 cathode there,
red, green, and blue. Usually
written in PCB KR for red cathode (red), KB for blue cathode (blue) and KG for
green cathode (green). Note the screen changes when
we do this step. Dominant
color will display red when we plug in the cathode was red, as well as for other
colors.If
the color on the screen does not change when we plug it into the cathode, should
be suspected damage to the tube (screen) from our tv. Although it
can happen from pin CRT connector loose.When
we express diagnostics our TV tube is not damaged, we can do small repairs to
replace an active / passive is in the little PCB. Usually transistors often broken.
If we
can not or are afraid to do it, we can call a service person. armed
with a mild diagnosis we had we could argue if the technician / handyman service
we declare tube / tv screen is broken.
Minggu, 09 Desember 2012
Langganan:
Posting Komentar (Atom)
Tidak ada komentar:
Posting Komentar